JP Group Front Stabilizer Mount Reinforcement Plate | Porsche 914 1970–1976 | OE 914 501 162 10, 2 Needed per Car (JP-3211-0)
Couldn't load pickup availability
JP Group Front Stabilizer Mount Reinforcement Plate — Porsche 914 1970–1976 (JP-3211-0)
Short answer: JP Group JP-3211-0 is the reinforcement plate for the front stabilizer (sway bar) mounting on the Porsche 914, 1970–1976, including 914/4 and 914/6. It replaces Porsche OE 914 501 162 10 (JP Group 1684001200). Two are needed per car, one per side, and it is sold each.
Part numbers: JP-3211-0 · OE 914 501 162 10 (91450116210) · JP Group 1684001200 · UPC 707924560404.
Fitment
| Years | Vehicle | Notes |
|---|---|---|
| 1970–1976 | Porsche 914 (914/4 1.7, 1.8, 2.0) | Front, per EMPI. Two per car. |
| 1970–1972 | Porsche 914/6 | Same front chassis; OE number shared |
| Any | Rear sway bar mount | Does not fit — the rear uses a different reinforcement |
| 1965–1989 | Porsche 911 / 912 | Does not fit — different chassis |
| 1968–1979 | VW Bus / Beetle | Does not fit |
Specifications
| Spec | Detail |
|---|---|
| Brand | JP Group (Denmark), distributed by EMPI |
| Part number | JP-3211-0 |
| OE reference | 914 501 162 10 |
| JP Group reference | 1684001200 |
| UPC | 707924560404 |
| Material | Steel |
| Position | Front stabilizer mount, left or right |
| Quantity per car | 2 |
| Weight | Approx. 0.25 lb (estimate; EMPI lists 0.018 lb) |
| Package (EMPI) | 5 x 4 x 1 in |
| Sold as | Each |
What's Included
- One reinforcement plate. Order two for a complete car.
Not Included
- Stabilizer bar, bushings and brackets
- Stabilizer link and mounting bolts
- Welding supplies, primer and seam sealer
Why It Matters
On the 914 the front sway bar loads the body where it mounts. Decades of cornering loads, rust and in some cases track use crack the original mounting area or tear it away from the body. Signs include clunks over bumps and in turns, a sway bar that has visibly moved and cracked paint or seam sealer around the mount. When you are doing front-end rust repair, a sway bar upgrade or a chassis-stiffening job, new reinforcement plates restore the original strength at a known weak point. Fitting them is far cheaper than repairing a torn-out mount later.
Installation Notes
- This is a body repair part. Plan on cutting out damaged metal and welding the plate in, following the original spot-weld pattern.
- Locate the plate exactly where the original sat so the sway bar bracket lines up. Measure from the opposite side or use a reference car.
- Clean to bare metal, use weld-through primer and seam-seal after welding.
- Prime, paint and apply cavity wax so the new plate does not rust like the old one.
- Refit the sway bar with new bushings while you are there.
Frequently Asked Questions
Does this fit my 1974 914 2.0?
Yes. EMPI lists JP-3211-0 for 1970–1976 Porsche 914, front.
How many do I need?
Two per car, one on each side. Each is sold individually.
Is this the same as OE 914 501 162 10?
Yes. EMPI and JP Group cross-reference JP-3211-0 to Porsche 914 501 162 10.
Left or right?
EMPI lists one part number for the front. Compare with your car to confirm the same plate is used on both sides.
Does it fit a 914/6?
Yes. The 914/6 shares the front chassis structure.
Is it new?
Yes, a new JP Group part.
Does it fit the rear sway bar mount?
No. This plate is for the front mount only.
Explore Related Categories
Porsche 914 Parts Porsche Suspension & Steering Suspension & Components
California Prop 65 Warning: This product can expose you to chemicals including lead and/or lead compounds, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit www.P65Warnings.ca.gov. Legal for use on pre-pollution-controlled vehicles only.
